CAR PAINT 2K ACRYLIC BRITISH GAS LT5B BLUE GLOSS 12.5Litre KIT

  

AWEL WHERE THE BEST COSTS LESS. 2K PAINT KIT GLOSS FINISH.

This kit consists of: 5 Litre 2k 2K Acrylic Paint - 2.5 Litre 2K Fast air dry hardener. 5 Litre 2k Fast Premium Thinner.

Uality approved, most of the paint we sell is manufactured by. Valspar Automotive and many more.

Are one of the largest independent suppliers of automotive paint in the UK and have been trading for over 45 years. We can supply this paint, at this very special price, in over 100,000 car - commercial and industrial colours / variants including a full range of RAL and B. 2K Acrylic paint available in Satin - Matt and Gloss finishes Jawel 2k Acrylic Paint is a very hard wearing versatile material and not affected by UV rays it is also stone chip and petrol resistant, once fully cured. The drying time can be determined by the type of 2k hardener used (Fast or Slow Air Dry) We recommend and supply as standard the 2k Fast air dry hardener, slow hardener is ideal for painting a very large areas or use in low bake ovens. This paint will not dry without the use of 2k hardener.

Please note a lot of metallic and pearl colours can only be matched in basecoat they are not available in 2k acrylic. This depends mainly on the type of hardener used and weather conditions but as a guide standard fast air dry hardener is dust free in 15 - 30 min Slow air dry hardener 30 - 45 min. Winter conditions, rocket accelerator can also be added to speed up drying time. Mixing Ratio: 2 parts 2k acrylic paint 1 part 2k Hardener the add 10% 2k Thinner to the final mix. You should be able to spray a small car or van with 2.5 litres of paint or equivalent area.

Technical and Material Health and safety. Data sheets are available for this product on request. Opening Hours: Mon-Friday 9.00am - 5.00pm Sat 9.00am -12.00pm. Awel sales & collection outlets. Unit 6 Hanford Close, Stoney Stanton Road, CV6 5TL. 285 Slade Road, Erdington, Birminghamham, B23 7JX. 1082 Pershore Road, Ten Acres End, Stirchley, B30 2YG. Estate, Watling Street, Staffs, B77 5BZ.

336-338 Cannock Road, West Midlands, WV10 ORB. Units 313-317 Heath Street, B66 2QY. 53B Aston Road Bromsgrove B60 3RD. IT IS IMPORTANT THAT YOU CHECK. The contents of your consignment before you sign.

THE PAINTERS 6 TIPS ON USING THE FOLLOWING 2K PRODUCTS. 2K ACRYLIC PAINT - 2K PRIMER - 2K CLEAR LACQUER. (1) 2K Air Dry Paint: Carry out any repairs, making sure you do not overlap the body filler over the existing paintwork. Treat any rust spots with Ferrozinc rust cure, spot primer and bare metal with Jawel self-etch primer. Mixing ratio: 1 part etch primer, 1 part etch solution or for a small area use the Pro-XL aerosol of etch primer.

(2) Flat the car with 600 grit wet/dry paper or 400 grit DA Discs, remove any dust with an air blow gun, then use a tack cloth before you wipe with Jawel panel wipe wax and grease remover. (3) 2K Jawel Primer Filler: Mixing ratio: 4 parts primer 1 part 2K hardener then add 10% - 15% 2K thinners to total volume mix, this can vary depending on the spray gun set up. STIR WELL and only mix the amount of material you intend to use in one application. Apply a cover coat and leave for 10 - 15 minutes depending on weather conditions, then apply a second coat, you may need to apply a third coat depending on your spray gun set up.

When dry de nib primer with a fine wet/dry paper 600 or 800 grit. Remove any dust then tack cloth the surface. Avoid leaving the primer overnight in a damp workshop if possible as primers are porous so it could absorb moisture resulting in poor top coat adhesion. (4) Prepare the workshop for spraying the top coat. Dampen the floor and if possible earth the car.

2K Paint and clear coats build up static and will draw bits from your hair and clothes. I strongly recommend you wear painter's hooded overalls. It is a must that you use the correct protection: Face Mask, Painters overalls and gloves and only use in a well ventilated workshop. (5) 2K Paint: STIR WELL AND CHECK COLOUR.

Most colour problems are caused because the paint has not been stirred thoroughly. Mix the paint: 2 parts paint, 1 part 2K Hardener then add 10% 2K Thinner to volume, this may vary depending on spray gun setup and air supply. Apply a cover coat of 2K paint, leave for 10-15 minutes, depending on conditions. 2K Paint is a direct high gloss paint if applied correctly, you should not require any 2K clear lacquer. (6) 2K Paint and Clear Coats are direct high gloss materials and when applied correctly, you should have no need to cut and polish.

If you do, I would recommend you leave overnight and then use the new AG3 Advanced liquid compound. Runs in the paint or lacquer: if you happen to get a run in the paintwork, this, in most cases can be flatted out. I have found the best way is if you use 1500 or 2000 grit wet/dry paper rub on a bar of soap and lightly flat the run. Do not try and flat out in one application, lightly flat then leave for a couple of hours or longer and do the same again taking it away in stages.

This is only my basic guide, if you require more information please have a look on our website for the manufacturers Data sheets. 2K ACRYLIC PAINT OR CLEAR LACQUER PLEASE NOTE YOU WILL NEVER GET A 100% MATT OR SATIN FINISH DUE TO THE NATURE OF THE MATERIAL, THEY WILL ALWAYS HAVE A SLIGHT GLOSS SHEEN.

IMPORTANT NOTICE REGARDING SOLVENT BASED PAINTS. We can supply a full range of compliant materials to suit all of our customers' Requirements including Water Based paint. Non-compliant solvent based paint will still be available for customers spraying industrial plant and machinery only. We have a massive colour range including: British Standard - RAL and most car, commercial and motorcycle colours.